| BEFORE
YOU BEGIN:
- All products are designed for installation on the
outside of the vehicle.
- Required Items include an installation squeegee
(included), masking tape, glass cleaner, dry paper
towels, measuring tape or ruler.
- Do not apply any vinyl graphics in direct sunlight.
Make sure it is between 60 degrees and 80 degrees
F
- Do not store unapplied graphics in direct sunlight
- damage may occur.
- All dirt, grease and wax must be removed from the
car surface before the decal is applied. This includes
wax from mechanical car washes, rain-x, compound,
etc. Failure to take this step may result in the decal
not sticking to the vehicle surface.
CARE
AND MAINTENANCE:
Once the decal is installed, to keep it looking new,
simply wash it whenever you wash the vehicle. You
can apply car wax, clearcoat, or RainEx over the decal
once it is applied. your new decal will give you years
of great looks. If you are in cold climate be careful
when using an ice scraper on any surface where decals
are applied.
| STEP
1 - UNPACK THE SHIPPING CONTAINER |
 |
Remove
the blank strip from packaging. Lay the strip
flat on a smooth table in an area that is at least
60° F and below 80° F. The strip should
be approximately 24"x60" |
| Inspect
decals for damage during shipment. We double-check
all orders are checked prior to shipment for
damage. Any damage incurred during shipping
must be reported to us within 48 hours. |
| STEP
2 - SLICE THE STRIP IN HALF |
| |
Using
a razor blade and a straight edge, cut the strip
in half (making two 12in by 60 in strips). Each
kit has enough material to make two windshield
strips 12"x60".
|
| Be
sure when you make the cut that it is along
the long side of the strip.. |
| STEP
3 - PREPARE THE SURFACE |
| |
The
most important step during decal installation
is making sure the installation area is clean
and dry. Make sure there is NO WAX, RAIN-X, COMPOUND,
lint, dust, or other residue on the surface. Remove
all wax, compound residue, car wash protectant,
etc with PREP-SOL, laquer thinners, brake cleaner,
409, Fantastic, etc. After cleaning the surface,
go over the surface with regular glass cleaner.
Wipe it dry. |
| All
waxes, oils, and polish must be removed from
the vehicle surface to insure that the decal
will stick properly Make sure the area is at
least 60° F and no hotter than 80° F. |
| STEP
4 - MARK THE WINDSHIELD |
| |
With
a tape measure and parking pencil, measure and
mark the windshield post where the desired bottom
edge will be of the strip when installed. Be sure
to measure down the same amount on both sides
of the windshield. Be sure to check your local
laws regarding placement of vinyl on the windshield.
|
| Measuring
and marking the posts will ensure that the strip
is straight when installed. |
| STEP
5 - PLACE ONE SECTION OF THE BLANK STRIP IN PLACE |
|
With
a friend's help, take on of the blank strips,
and hold it across the windshield (turn the strip
so that the edge you cut is on top. This makes
the straight factory vinyl edge facing towards
the bottom) There should be extra on top past
the top of the window.
|
| Normal
drop strips are between 4 and 6 inches. There
should be extra vinyl on top above the window.. |
| STEP
6 - TAPE IT TO THE WINDOW |
| Using
two small pieces of masking tape, temporarily
hold the strip in place by taping the bottom edge
of the strip to the windshield in the desired
location. With scissors or a razor blade, CAREFULLY
cut around the sides and the top of the windshield
leaving at least 1 inch extra all around. The
extra will be removed during final installation. |
|
| The
extra will be removed during final installation |
| STEP
7 - SECURE THE STRIP |
| |
With
a friend's help, place a long piece of tape along
the bottom edge of the strip, half on the strip
and half on the window, securing it. Fold the
entire strip down along the hinged area you just
made. |
| The
hinged flap will make installation much easier.
For long thin designs, you can cut the decal
in half (up and down between the lettering)
once it has been taped to create two flaps for
even easier installation. |
| STEP
8 - START REMOVING BACKING PAPER |
| Raising
the large hinged 'flap', and begin to peel the
wax paper backing off the strip (exposing the
sticky side of the decal). Spray a light mist
of water (water only, NO SOAPY SOLUTIONS!!!!)
|
|
| Using
a spray bottle filled with regular water is
important. Soapy solutions tent to keep the
decal wet and may lead to the strip flying off
at high speeds. |
| STEP
9 - BEGIN DECAL APPLICATION |
| |
With
the wax paper backing peeled half way downward,
begin to apply the sticky side of the strip to
the vehicle surface with the Free application
tool enclosed. Besure to use even strokes horizontally
across the decal. |
| Continue
to spray a LIGHT coating of water onto the window
surface. Too much water will lead to the strip
not drying properly. Not enough water will make
it stick prematurely. |
| STEP
10 - CONTINUE INSTALLATION |
| Continue
smoothing out the strip with long hoizontal strokes,
starting at the top and working towards the bottom.
Continue to remove the backing paper as needed. |
. |
| Only
remove the wax paper backing as needed. The
sticky side of the decal should be covered until
installation. This will keep it from getting
dirty and sticking to the vehicle surface prematurely. |
| STEP
11 - TRIM AROUND THE WINDSHIELD POST |
| |
Once
the entire strip is applied, use a razor blade
to trim the strip at the edge of the window. Take
your time and be patient. Cutting it too short
will result in a rough edge. Cutting it too long
may result in it getting caught on something. |
| |
| STEP
12 - FINISH INSTALLATION |
| Once
the strip has dried for at least 2 hours, apply
wax or rain-x over the strip and window surface.
This will keep the wipers from damaging the strip
during normal use. |
. |
| Most
bubbles will dissipate within 3 weeks of installation
due to sunlight. |
All
of our products are custom made to order. There are
no refunds, no exchanges and no returns on any of
our products. If you destroy the decal during installation,
we may offer you a replacement at a reduced cost.
In order to qualify for a lower cost replacement,
you must send us the damaged decal. Management reserves
the right to modify this policy.
QUESTIONS
OR COMMENTS
SHOULD BE DIRECTED TO
SGS Inc Info Line at (732) 635-0101
or
Superior Graphics & Signs, Inc.
PO Box 295
Adelphia NJ 07710-0295
This page is protected by U.S. and International Copyrights.
Any duplication or distribution of this information
in any form is illegal. We have successfully prosecuted
content theft in the past and aggressively pursue
violators. The information has been imbedded with
searchable phrases which can be traced to any website
using them.
|
